Skip to content

How to Change Battery in Honda Key Fob

When you need to replace a CR2032 battery in your Honda key fob, you can learn how to do it yourself by following these instructions. You will also learn how to disassemble and reassemble the fob. This guide will walk you through the process step-by-step. Follow along as you learn how to change the battery in your Honda key fob. Once you’ve done all this, you can reassemble your fob and get back to driving your car.

to show key fob


Replace a CR2032 battery in a Honda key fob

To replace a CR2032 battery in – and repair a dead key fob – you need to find the correct part and remove the old one. Then, use a screwdriver or paperclip to pry open the battery case. Ensure that you remove all of the corrosion-causing materials such as oils and grease before installing the new battery. Once you have finished installing the battery, snap the key fob back together and test it.

To remove the battery, make sure to lay the fob flat on a table. Place a small screwdriver on the battery’s negative side. Carefully pry the battery out, and then slide the key fob half back together. The key fob is now ready for replacement. It will require a special programmer, which can be purchased at an authorized parts center or online at Mopar.

Depending on the type of vehicle you have, key fob batteries can vary from car to car. However, the most common ones are CR2025 and CR2032 3-Volt batteries. Your owner’s manual should provide information on the battery type for your particular model. Batteries like these can be found at any electronics store, or even at a dealership. To replace a key fob battery, follow the directions listed on the manufacturer’s website.

If you have a spare CR2032 battery, you can use a generic battery instead. While generic batteries are less expensive, they are not guaranteed to last as long as a name-brand battery. Before replacing the battery, make sure that you’ve checked all the connections and that they make contact with the battery. If the battery doesn’t fit correctly, you’ll have to reprogramme the key fob again. To do this, insert the key into the “On” position and hold it for a second.

In some cases, the fob’s battery can be too weak to provide enough power to the transmitter. This will result in a decrease in the range of the transmitter, which requires you to get closer to your car to start the engine. Additionally, if the battery is too weak, your push button car might not recognize the key and show a warning message on the driver display.

To replace a CR2032 battery in – or any other CR2032 battery – in a Honda key fob, you must remove the rear of the fob and remove the battery’s connector. A CR2032 battery in a Honda key fob is typically made of lithium-ion technology and can last for up to six years. Depending on the model, replacing this battery may only take a few minutes.

A CR2032 battery is typically used in the CR2032 Honda Smart Key. This type of battery comes in a two-pack and is a standard CR2032 size. The average life of a CR2032 is two to five years. The CR2430 battery, on the other hand, cannot be interchanged with a CR2032.

It’s not difficult to replace a CR2032 battery in – or any other CR2032 battery for that matter – since they’re widely available. Most hardware stores, convenience stores, and major retailers carry CR2032 batteries. Single packs of CR2032 batteries are generally priced between $2 and $3, and six-packs are often priced at $10 to $15.


Reassemble a Honda key fob

To reassemble a Honda key fob to replace the battery, insert the new battery and reconnect the faceplate. Press the two pieces together until they snap together. You may want to take your spare key fob with you when changing the battery. Afterwards, you can call Westbrook Honda to replace the key fob for you. Now you can drive your car again! Remember, it’s never easy to replace a key fob.

While changing the battery is a fast, convenient, and easy process, some key fobs cannot be repaired using these steps. It’s important to remember that replacing the battery should be done by an expert if you’re not familiar with electronic circuitry. You should also never touch the circuits with bare hands. Once you’ve finished cleaning the circuitry, reassemble the key fob to replace the battery.

To reassemble a Honda key fob, you must first turn the ignition off. After that, turn the ignition to the “Off” position. Hold the lock button for one second. After the door cycles, the key will enter remote programming mode. To remove the battery, follow the steps in the reverse order. If you’re not sure how to unlock the key fob, consult your owner’s manual to learn how to remove and reassemble it.

Changing the battery in a Honda key fob is a relatively simple process. It should only take a few minutes. To prevent further frustration, you can seek assistance from a certified Honda service center. They will be able to replace the battery for you. Reassembling a Honda key fob is easy, and will save you time and money! For a more thorough procedure, visit a Honda dealer in Toms River, NJ.

Sources

Panasonic CR-2032EL – Size: CR2032 – 3V – Lithium Power ✔. (2020, February 3). Panasonic Batteries; www.panasonic-batteries.com. https://www.panasonic-batteries.com/en/specialty/lithium-coin/coin-lithium-cr2032